OKS 641 Maintenance Oil, Spray

Areas of application:

• Dismantling of all seized or sticky components or machine elements
• Applicable on door locks, hinges, screws, bolts, bushings, cranks, linkages, valves, slide rails, cable pulls, shafts

Advantages and Beneifits:

• Highly effective due to combination of mineral oil and additives
• Broad range of maintenance sector uses
• Displaces moisture, protects against corrosion
• Cleans, maintains and lubricates
• Gets under rust

Technical Specifications:

• Lower operating temperature: -30°C
• Upper operating temperature: 60°C / 150°C
• Density (at 20°C): 0.83 g/cm³
• Viscosity (at 40°C): 3 mm²/s
• Coefficient of friction SRV (μ): 0.11 (ball, disk)
• Salt spray test: > 100 h
• UFI: 5DH1-Q0PM-X000-6EC4

OKS 451 Chain and Adhesive Lubricant, Spray

Areas of application:

• Rope drives and wire pulls
• Stacker truck chains
• Flat-link articulated chains
• Flexible drives, bowden and spring cables

Advantages and Beneifits:

• Outstanding creep and gap penetration
• Highly adhesive and resistant to throwing off
• Contains MoS₂-Active for performance
• Resistant to cold, hot water and saline solutions
• Excellent wear and corrosion protection
• O-ring neutral, Duolabel

Technical Specifications:

• Lower operating temperature: -30°C
• Upper operating temperature: 200°C
• Viscosity (at 40°C): 300 mm²/s
• Four-ball test rig welding load: 2,400 N
• UFI: VXD1-G02R-P006-RS1J

OKS 9631 Quick Dry - Autoconer Spray

Areas of application:

• Lubricant for textile machinery
• Used in autoconer machines for splicers and knotters

Advantages and Beneifits:

• Evaporates quickly leaving a thin lubricating film
• Provides corrosion protection
• Especially suited for splicers and knotters
• Does not stain threads
• Pleasant odour

Technical Specifications:

• Density: 0.70-0.75 g/cc @ +25°C

OKS 2901 Belt Tuning Spray

Areas of application:

• Increases tensile force by up to 50% for all kinds of V-belts, round and flat belts on fans, compressors, pumps, ventilators, mills
• Protects against drying out and wear
• Prevents belt squeaking and slip

Advantages and Beneifits:

• Increases service life
• Prevents squeaking
• Prevents slip
• Increases belt tension force

Technical Specifications:

• Operating temperature: up to +80°C

OKS 475 HS - High Speed Bearing Grease

Areas of application:

• Bearings operating in high speeds and extremely low breakaway torque
• Roller and needle bearings
• Precision bearings with low starting torque
• High speed spindles
• Lubrication of metal to plastic or plastic to plastic sliding surfaces
• Electronics industry as low resistance white grease

Advantages and Beneifits:

• High DN factor of 1,000,000
• Very low internal friction and extremely low starting resistance
• Does not get thrown off and resists oil separation
• Light synthetic oil ensures low friction and low resistance

Technical Specifications:

• Density (at 27°C): 0.85–0.90 g/cc
• Viscosity (at 40°C): 30 mm²/sec
• DN Factor: 1,000,000

OKS 2650 – Industrial Cleaner

Areas of application:

• Cleaning of cooling devices, vending machines
• Cleaning of tiles, ceramics or natural stone
• Construction machines and lorries, tarpaulins
• Machine tools and workshop floors

Advantages and Beneifits:

• NSF A1 registered
• No classification marks according to EG 1272/2008
• Free of organic solvents and phosphates
• Readily biodegradable
• Good separation behaviour
• Gentle to plastics, seals, rubber and sensitive metals
• Dilutable up to 1:10
• Suitable for high-pressure cleaners
• MOSH/MOAH-free

Technical Specifications:

• Density (at 20°C): 1.03 g/cm³
• pH value: 10.7 (concentrate)

OKS 201 MoS₂ Assembly Lubricant Grease

Areas of application:

• Shake the can before use
• Clear the surface and spray from 15 cm distance
• Turn can upside down after use to clear propellant gas

Advantages and Beneifits:

• Can is under pressure – do not puncture or incinerate
• Store away from sunlight or heat
• Use only in well-ventilated areas
• Keep out of children’s reach

Technical Specifications:

• Lower operating temperature: -50°C

OKS 2601 Cleaner and Degreaser Spray

Areas of application:

• Cleaning metal surfaces before surface treatment
• Cleaning bearings before lubrication
• Removing oil, grease, and dirt from assemblies
• Cleaning machines and components

Advantages and Beneifits:

• Strong cleaning power, good penetration, quick evaporation
• Fast-acting, cost-saving degreaser
• Jet spray provides easy cleaning
• Reduces manual intervention

Technical Specifications:

• Spray from 6–15 cm distance depending on jet strength
• Use in well-ventilated area or open air
• Avoid plastics like rubber, PVC, plexiglass etc.
• Store below 50°C away from heat

OKS 2801 - Leak Detector Spray

Areas of application:

• Piping and hoses including steel bottles, compressors, breathing devices, gas systems
• Fittings, flanges, valves, welded connections of pressure gas lines
• Suitable for air, refrigerants, acetylene, butane, natural gas, CO₂, oxygen, propane, town gas, nitrogen, hydrogen, ammonia

Advantages and Beneifits:

• Acts non-corrosive
• Visual inspection via bubble formation
• Tested to DIN EN 14291
• Suitable for spraying overhead

Technical Specifications:

• Operating temperature: up to +50°C

OKS 310 – 301 MoS₂ High-Temperature Lubricant

Areas of application:

• Lubrication of friction and rolling bearings, chains, joints at high temperatures
• Systems under radiation heat (painting, drying, firing)
• Dry lubrication above 200°C
• Lubrication of elastomers/plastics not resistant to mineral oil

Advantages and Beneifits:

• Highly suitable as a high-temperature lubricant
• Homogeneous MoS₂ distribution
• Resistant to water, chemicals, fuels, hydraulic oils

Technical Specifications:

• Upper operating temperature: 200°C (liquid lubrication)
• Density (at 20°C): 1 g/cm³
• Viscosity (at 40°C): 150 mm²/s
• Four-ball test welding load: 2,800 N
• UFI: VCUE-H0GS-K00R-56W5

OKS 410 – MoS₂ High-Pressure Long-Life Grease

Areas of application:

• Grease lubrication of unsheltered parts subject to heavy loading and/or impacts
• Friction, rolling and pivoting bearings, splined shafts, knockout spindles
• Threaded spindles and sliding surfaces of all kinds
• For harsh operating conditions

Advantages and Beneifits:

• Excellently suited as a safety lubricating grease
• Especially good wear protection in mixed friction sectors
• Effectively protects against corrosion
• Contains Mox-active to improve performance

Technical Specifications:

• Lower operating temperature: -20°C (≤ 1,400 hPa)
• Upper operating temperature: 130°C (F50 (A/1500/600), 100h)
• Consistency: 2 NLGI grade (DIN ISO 2137)
• Viscosity (at 40°C): 185 mm²/s (base oil)
• Four-ball test rig welding load: 3,600 N
• UFI: XMD1-F0A5-F007-3DQ9

OKS 420 – High-Temperature Multipurpose Grease

Areas of application:

• Gearbox lubrication of heavily loaded, slow-running toothed gearing
• Chain lubrication in conveyance and transport sector for water/steam exposure
• Bearing lubrication of friction and rolling bearings in various machinery

Advantages and Beneifits:

• Suited for corrosive conditions with high temp and pressure
• Economical due to optimised formula
• Reduces failure and supports long-term lubrication
• Highly adhesive, waterproof, noise-damping

Technical Specifications:

• Lower operating temperature: -10°C (≤ 1,400 hPa)
• Upper operating temperature: 160°C
• Consistency: 1-2 NLGI grade (DIN ISO 2137)
• Viscosity (at 40°C): 490 mm²/s (base oil)
• UFI: 35P3-G0PG-7001-U0QA

ISOFLEX LDS 18 SPECIAL A

Areas of application:

• Suitable for plain and rolling bearings at low temp and/or high speeds
• Grinding spindles, machine tool spindles, spindle bearings, textile spindles
• Bearings in OE-spinning turbines, precision and optical equipment

Advantages and Beneifits:

• Good corrosion and oxidation stability for cost savings
• Tried and tested for high speed and low temp use
• Low heat-up of bearings = longer service life

Technical Specifications:

• Applied by brush, spatula, grease gun or cartridge
• Check compatibility with elastomers/plastics before application

PETAMO GHY 133 N

Areas of application:

• High-performance lubricating grease for rolling bearings at high temp

Advantages and Beneifits:

• Resistance to high temperatures
• High oxidation resistance
• Efficient wear protection even at high temperatures
• Good corrosion and water resistance
• Formulated with polyurea thickener, synthetic and mineral oil, and additives

Technical Specifications:

CENTOPLEX GLP 202 BH

Areas of application:

• Detaching bottom roller
• Take off bottom roller
• Top nipper actuating shaft
• Nipper eccentric cam
• Brush shaft
• Table calendar shaft
• Front nipper support
• Nipper assembly
• Delivery drive shaft
• Detaching top rollers
• Nipper shaft greasing
• Unicomb shaft

Advantages and Beneifits:

• Top nipper threaded pin

Technical Specifications:

• Better water resistance and load carrying capacity
• Corrosion protection
• Excellent pumpability and low resistance to flow

POLYLUB GA 352 P

Areas of application:

• Lubrication of rolling/plain bearings, racks, guides, pneumatic cylinders
• Load rollers and slideways
• Food-processing machinery where no direct contact with food occurs

Advantages and Beneifits:

• Good water resistance
• Good adhesion
• NSF H2-registered

Technical Specifications:

• Can be applied by brush, spatula or grease gun

Klüber Altemp Q NB 50 Lubricating Paste

Areas of application:

• Assembly of frictional connections, lubrication of clamping chucks
• Scroll, cam and spiral chucks
• Resistant to water and media like cooling lubricants

Advantages and Beneifits:

• Low lubricant cost due to long service life
• Good wear and corrosion protection
• High pressure absorption capacity for clamping forces
• Prevents tribo- and fretting corrosion

Technical Specifications:

Klüberplex BE 31-222

Areas of application:

• Rolling and plain bearings
• Pivoting bearings
• Small gears
• Sealing and lubricating greases for labyrinth seals and industrial valves and fittings

Advantages and Beneifits:

• Longer component life due to reduced wear and good pressure absorption capacity
• Reduced maintenance due to good sealing effect and resistance to water and other media
• Long relubrication intervals and food ageing and oxidation stability
• NSF H2 registration allows use in food-processing industry (no direct food contact)

Technical Specifications:

• Can be applied by grease guns, brush or spatula
• For application via central lubrication systems, check pumpability with manufacturer

Klüberquiet BQH 72-102 Lubricating Grease

Areas of application:

• Rolling bearing grease for low noise environments
• Synthetic high-temperature grease for precision components

Advantages and Beneifits:

• High temperature resistance with high purity
• Excellent corrosion protection and cleanliness
• Displaces moisture and gets under rust

Technical Specifications:

Klüberoil GEM 1-220 N

Areas of application:

• Modern gears with increasing power density

Advantages and Beneifits:

• Exceeds CLP requirements (DIN 51517-3)
• High-performance mineral oil-based gear oil

Technical Specifications:

• Form: Oil
• Standard: DIN 51517-3
• Type: Mineral oil

Klübersynth GEM 4-320 N

Areas of application:

• Modern gears
• All gear components

Advantages and Beneifits:

• High scuffing load capacity
• Excellent wear protection for gears and rolling bearings
• High micropitting resistance (GFT ≥ 10)
• Longer service life due to oxidation resistance
• Low foaming and anti-corrosive properties
• Excellent viscosity-temperature behavior
• Reduced energy consumption due to friction optimization

Technical Specifications:

• Standard: DIN 51517-3
• Tested: FVA 54/7
• Seal compatibility: 72 NBR 902, 75 FKM 585, 75 FKM 260466, 75 FKM 170055

Klübersynth GH 6-1000

Areas of application:

• Worm gears
• Bevel and spur gears
• Rolling and plain bearings

Advantages and Beneifits:

• High micropitting resistance (FVA 54 GFT ≥ 10)
• Low wear and reduced friction
• Long service life
• Efficient lubrication even at high temps
• Seal compatibility with several elastomers
• Approved by major gearbox manufacturers

Technical Specifications:

• Standard: DIN 51517-3 CLP
• ISO VG 220 meets API GL-5
• Base: Polyglycol
• Temperature: Max 80°C (NBR), higher with FKM

Klüberoil GEM 1-320

Areas of application:

• Modern gears with increasing power density

Advantages and Beneifits:

• High scuffing load capacity
• Excellent wear and corrosion protection
• Long service life and reduced maintenance
• Low foaming and good oxidation stability

Technical Specifications:

• Standard: DIN 51517-3 CLP
• Type: Mineral oil
• Application: Gear and multipurpose oil

Eni Acer EE 10

Areas of application:

• High-speed spindles of machine tools
• Knitting machinery, stocking needles, pneumatic tools
• Hydraulic systems requiring low viscosity oil

Advantages and Beneifits:

• Very low viscosity for high-speed operations
• Anti-rust, antioxidant, and anti-wear additives
• Energy efficient lubricant

Technical Specifications:

• Viscosity at 100°C: 2.7 mm²/s
• Grade: SO 10 EE
• Form: Oil

Eni RGB 220

Areas of application:

• Enclosed gears under heavy loads and high speeds
• Couplings, transmission screws, low-speed plain bearings
• Oil mist lubrication systems

Advantages and Beneifits:

• Withstands elevated temperatures and high sliding velocities
• Suitable for splash and circulation lubrication

Technical Specifications:

• Specs: ISO-L-CKD, ANSI/AGMA 9005-D94, ASLE EP, DIN 51517 Teil 3 CLP, U.S. Steel 224

Eni Hydraulic Oil 32,46,68,100,150

Areas of application:

• Automobile and heavy vehicle hydraulic systems

Advantages and Beneifits:

• High-quality base oil composition
• Covers full viscosity range for industrial uses
• Recognized brand in lubrication technology

Technical Specifications:

• Packaging Size: 210 L
• Viscosity Grades: VG 32, 46, 68, 100, 150
• Density: 833 kg/m³

Eni Multipurpose Grease

Areas of application:

• Automotive: Wheel bearings, chassis, steering
• Industrial machinery
• Earthmoving, mining, and farm equipment

Advantages and Beneifits:

• Exceeds IS 7623 and IS 12203 standards
• Effective under moderate to heavy loads

Technical Specifications:

• Packaging Size: 26 kg
• Form: Grease
• Packaging Type: Pail

Kluebersynth GE 4 75W-90

Areas of application:

• Spur, bevel and hypoid gears
• Drives in rail vehicles, robots, textile machines, forming presses

Advantages and Beneifits:

• API GL-5 scuffing protection
• Excellent wear and micropitting resistance
• Good viscosity-temperature and anti-foam behavior
• Oxidation and ageing resistant

Technical Specifications:

• Viscosity Grade: 75W-90
• Standard: API GL-5
• Base: Synthetic

V – PULLEY Z

• PIX V BELT
• RANGE: A,B,C,D,AA, BB
• WRAPPED SECTION : AX,BX,CX
• RANGE: SPA,SPB,SPC,SPZ
• WEDGE SECTION: XPA , XPB,XPC,XPZ
• NARROW SECTION: 3V,5V,8V,3VX,5VX,8VX

TIMING PULLEY

• PIX TIMING BELT:
• STD (STANDARD TEETH DRIVE): S5M,S8M
• HTD (HEAVY TEETH DRIVE): 5M,8M ,14M
• CLASSICAL SECTION: XL,L ,H, XH

FLAT PULLEY

• ELGI FLAT BELT:
• GG – RUBBER - RUBBER
• GR -- RUBBER - GROOVED
• LT – LEATHER – FABRIC
• LL – LEATHER – LEATHER
• GGX – TANGENTIAL BELT
• GT – RUBBER -TEXTILE

CONVEYOR PULLEY

• ELGI CONVEYOR BELT:
• EM 8 / 2 CONVEYOR BELT